Description: 估算在给定门限下常用输入信号的带宽。函数将代表待分析波形的矢量signal作为输入-estimate in a given threshold under the common input signal bandwidth. Function will be representative of the waveform analysis as input vector signal Platform: |
Size: 1024 |
Author:meimei |
Hits:
Description: 高分辨率要求系统具有大的带宽，瞬时带宽的增加必将提高系统对硬件的要求，本文采用方便灵活的步进频率波形信号。脉间频率步进波形通过子脉冲载频的步进变化来获得大的有效带宽，使成像具有高分辨率，采用加窗和补零方法提高信噪比，但该信号对目标径向速度非常敏感。采用补零方法提高距离取样分辨率，使距离像细化，并用公式说明了补零只能提高距离取样分辨率，并不能改变频率步进信号的距离分辨能力。该信号波形对目标径向速度的敏感，使目标能量分散到邻近的距离单元造成距离分辨率下降，如果不事先进行速度补偿，直接对回波信号进行逆傅立叶变换，将使所成一维距离像发生频谱展宽，并伴有距离像发生平移。本文证明了当目标有径向速度时仍采用对回波信号直接进行逆傅立叶变换的方法将使一维距离像发生频谱展宽并伴有距离像发生频移，从而严重影响了一维距离像的质量。-high-resolution requirements of the system with large bandwidth, the increased instantaneous bandwidth will improve the system of hardware, In this paper, a flexible and convenient step frequency signals. Pulse frequency step-pulse waveform through the carrier frequency step to achieve great changes in the effective bandwidth. make imaging with high resolution, increasing the window and fill methods to improve signal-to-noise ratio is, However, the signal on the target radial velocity is very sensitive. Using zero-distance sampling method to improve resolution, so that distance as refinement, and formulates a zero-distance sampling can improve resolution, does not alter the frequency of the signal from stepping resolution capabilities. The signal waveform on the target radial velocity sens Platform: |
Size: 2048 |
Author:石榴石 |
Hits:
Description: 格状编码调制是为解决卫星通信中信道噪声对接收的影响及带宽的限制而产生的，其将信道编码与调制很好的结合起来，并且能发挥各自的优点，这种方法在不增加带宽和相同的信息速率下可获得3~6dB的功率增益。-trellis coded modulation for satellite communications solutions Channel noise on the receiver bandwidth and the impact of the restrictions, it will channel coding and modulation good combine, and can play to their respective advantages, This method does not increase in the same bandwidth and speed of information available under the three-6dB gain power. Platform: |
Size: 7168 |
Author:GF |
Hits:
Description: pashload是应用在linux下的网络带宽测试源程序精确度比较高
/////////////////////////////////////
Pathload is a tool for estimating the available bandwidth
of an end-to-end path from a host S (sender) to a host R (receiver).
The available bandwidth is the maximum IP-layer
throughput that a flow can get in the path from S to R,
without reducing the rate of the rest of the traffic in the path.
-is used in pashload under linux network bandwidth testing the accuracy of a relatively high source /////////////////////////////////////Pathload is a tool for estimating the available bandwidthof an end-to-end path from a host S (sender) to a host R (receiver). The available bandwidth is the maximum IP-layer throughput that a flow can get in the path from S to R, without reducing the rate of the rest of the traffic in the path. Platform: |
Size: 68608 |
Author:h |
Hits:
Description: 脉冲编码调制（PCM）用于在数字传输媒体上传送模拟信号，在PCM中，首先对模拟信号以高于其带宽两倍的奈奎斯特率进行采样，然后对所得样本进行量化。采用不同量化级别生成的PCM编码会影响接收器重建模拟信号的质量。 -Pulse code modulation (PCM) for the media in the digital transmission of analog signal transmission in the PCM, the first analog signal to more than the Nyquist rate of twice the bandwidth sample, and then to quantify the samples. Using different quantization level generated PCM coding receiver will affect the quality of the reconstruction of analog signals. Platform: |
Size: 1024 |
Author:jack |
Hits:
Description: 在软件接收机的基础上,利用鉴频器辅助鉴相器的输出,引入一个模糊逻辑控制器,使得环路能够智能跟踪信号的动态变化.实验结果证明所提出的设计方法与传统环路相比可大幅度缩短跟踪时间,减小环路滤波器带宽,并能消除周跳.-In the software receiver, based on the use of auxiliary frequency discriminator phase detector output, the introduction of a fuzzy logic controller, the loop can be intelligent tracking signal dynamics. The experimental results demonstrate that the proposed design method with the traditional loop phase than we might have to significantly reduce the tracking time, reduce the loop filter bandwidth, and can eliminate the cycle slips. Platform: |
Size: 344064 |
Author:何宁 |
Hits:
Description: ofdmsourceCode用matlab仿真实现了25 kHz 带宽内同时传送总共48 kbits 的两路语音-matlab simulation ofdmsourceCode achieved with 25 kHz bandwidth at the same time send a total of 48 kbits of two-way voice Platform: |
Size: 26624 |
Author:木木 |
Hits:
Description: 数字信号处理中经典的FFT算法实现，对理解信号处理帮助很大-A Fast Fourier Transform [FFT] method for frequency sparse functions. Recovers the k most energetic frequencies hidden in a bandwidth-N function in k*polylog[N] time. Platform: |
Size: 149504 |
Author:zhaohui |
Hits:
Description: Spread-spectrum techniques are methods by which electromagnetic energy generated in a particular bandwidth is deliberately spread in the frequency domain, resulting in a signal with a wider bandwidth. These techniques are used for a variety of reasons, including the establishment of secure communications, increasing resistance to natural interference and jamming, and to prevent detec Platform: |
Size: 11264 |
Author:Mathis |
Hits:
Description: QPSK modulation system with recover loops-This is a model of a QPSK modulation system for transmission over a bandpass channel with fc = 100 Hz and B = 30 Hz and AWGN at the receiver. SRRC fi lters with excess bandwidth α = 0.18 are employed. The receiver includes an NDA timing recovery loop followed by a DD phase recovery loop. The transmitter?s symbol period is T and set to a value of 100 ms. The symbol period at the receiver is Tr. The model will produce six windows: Two constellation plots and two eye diagrams (for the real part only), at the output of the matched fi lters and after the recovery loops a plot of the phase error (output of the NCO) and a plot of the fractional timing error (used in the interpolator). The frequency off set at the receiver is denoted by deltaf. The model simulates the transmission of 8000 QPSK symbols. Platform: |
Size: 15360 |
Author:ranbowang |
Hits:
Description: QPSK信号在MATLAB上的仿真代码，载波频率为10HZ，信息速率为1Baud，信号经过带宽为2HZ的系统。-QPSK signal in the simulation of MATLAB code, the carrier frequency to 10HZ, the information rate of 1Baud, signal bandwidth of the system 2HZ. Platform: |
Size: 706560 |
Author:小武 |
Hits:
Description: This matlab code generates UWB indoor channel impulse response described in :
Cassioli, D. Win, M.Z. Molisch, A.F., "The ultra-wide bandwidth indoor channel: from statistical model to simulations," Selected Areas in Communications, IEEE Journal on , vol.20, no.6, pp. 1247-1257, Aug 2002
URL: http://ieeexplore.ieee.org/stamp/stamp.jsp?arnumber=1021916&isnumber=21989
All parameters of the channel were taken from the reference paper
-This matlab code generates UWB indoor channel impulse response described in :
Cassioli, D. Win, M.Z. Molisch, A.F., "The ultra-wide bandwidth indoor channel: from statistical model to simulations," Selected Areas in Communications, IEEE Journal on , vol.20, no.6, pp. 1247-1257, Aug 2002
URL: http://ieeexplore.ieee.org/stamp/stamp.jsp?arnumber=1021916&isnumber=21989
All parameters of the channel were taken from the reference paper
Platform: |
Size: 38912 |
Author: |
Hits:
Description: Simulation of Residual Excited Linear Prediction (RELP) coding for speech:
This simulation give your voice or available clear wav file.This encoder have linear predictor that decreases signal s dynamic (lower quantization level). This technique also use lowpass filtering to make lower bandwidth and reconstruct it with three methods that is chosen in decoder. For example duplicate same spectrum of encoded signal that filtered in upper frequency.-Simulation of Residual Excited Linear Prediction (RELP) coding for speech:
This simulation give your voice or available clear wav file.This encoder have linear predictor that decreases signal s dynamic (lower quantization level). This technique also use lowpass filtering to make lower bandwidth and reconstruct it with three methods that is chosen in decoder. For example duplicate same spectrum of encoded signal that filtered in upper frequency. Platform: |
Size: 855040 |
Author:Ardalan |
Hits:
Description: The purpose of this project is to create a different system for processing voice signals and from which we draw useful conclusions about these brands.
More specifically, the system will first filter the voice signal with a pass bandwidth (chebyshev probably type 2) to reduce the presence of noise in it and then we can calculate:
• what limits the signal word out (segmentation)
• how are these words
• the characteristic frequency of the voice of the speaker of each file (voice pitch). -The purpose of this project is to create a different system for processing voice signals and from which we draw useful conclusions about these brands.
More specifically, the system will first filter the voice signal with a pass bandwidth (chebyshev probably type 2) to reduce the presence of noise in it and then we can calculate:
• what limits the signal word out (segmentation)
• how are these words
• the characteristic frequency of the voice of the speaker of each file (voice pitch). Platform: |
Size: 2048 |
Author:Pastel87 |
Hits:
Description: N=15, 。用Hanning窗设计一线性相位带通滤波器，观察它的实际3dB和20dB带宽。N=45，重复这一设计，观察幅频和相位特性的变化，注意长度N变化的影响。-N = 15,. Hanning window design with a linear-phase band-pass filter, observe its actual 3dB and 20dB bandwidth. N = 45, repeat the design, observe the amplitude-frequency and phase characteristics of the change, pay attention to the length of N changes. Platform: |
Size: 20480 |
Author:lm |
Hits:
Description: An 8-QAM communications channel simulation in Simulink, constructed from a 16-QAM model and using an I,Q correlation receiver.
QAM (quadrature amplitude modulation) is a method of combining two amplitude-modulated (AM) signals into a single channel, thereby doubling the effective bandwidth. QAM is used with pulse amplitude modulation (PAM) in digital systems, especially in wireless applications. In a QAM signal, there are two carriers, each having the same frequency but differing in phase by 90 degrees (one quarter of a cycle, from which the term quadrature arises). One signal is called the ‘I’ signal, and the other is called the ‘Q’ signal. Mathematically, one of the signals can be represented by a sine wave, and the other by a cosine wave. The two modulated carriers are combined at the source for transmission. At the destination, the carriers are separated, the data is extracted from each, and then the data is combined into the original modulating information. -An 8-QAM communications channel simulation in Simulink, constructed from a 16-QAM model and using an I,Q correlation receiver.
QAM (quadrature amplitude modulation) is a method of combining two amplitude-modulated (AM) signals into a single channel, thereby doubling the effective bandwidth. QAM is used with pulse amplitude modulation (PAM) in digital systems, especially in wireless applications. In a QAM signal, there are two carriers, each having the same frequency but differing in phase by 90 degrees (one quarter of a cycle, from which the term quadrature arises). One signal is called the ‘I’ signal, and the other is called the ‘Q’ signal. Mathematically, one of the signals can be represented by a sine wave, and the other by a cosine wave. The two modulated carriers are combined at the source for transmission. At the destination, the carriers are separated, the data is extracted from each, and then the data is combined into the original modulating information. Platform: |
Size: 11264 |
Author:Griffin Wright |
Hits:
Description: 为了提高移动通信系统中数据传输的有效性能,降低GMSK调制系统的误码率. 首先对GMSK调制系统进行分析,得到不同BT值GMSK调制的移动通信系统误码率和带宽的关系.通过引入具有纠错性能的编码技术,降低信息传输的误码率,提高系统的有效性. 本文给出了引入编码技术的GMSK调制系统的仿真模型,仿真结果表明,在相同的信噪比下,系统的误码率降低了1～2dB.-This paper mainly intends to improve the performance of the communication system and decrease the error bit rate of the information. First , the GMSKmodulation system was analyzed , and the relation of the BER and
bandwidth in the different BT value was obtained. By introducing the encoding technology , the error bit rate of the information was lowered so that the performance of systemwas improved. This paper presents a simulated model . The results show that the BER of the system in the same SNR can lower 1 to 2 dB. Platform: |
Size: 582656 |
Author:Jonny |
Hits:
Description: 线天线阵和面天线阵在MATLAB内的方向图以及半功率带宽-Antenna array and antenna array within the orientation map in MATLAB and the half-power bandwidth of Platform: |
Size: 3072 |
Author:杨康 |
Hits:
Description: 随着信息容量的增加和频率资源的稀缺，为提高单位频带利用率，在微波通信系统中越来越多地采用多电平多相位的复杂信号调制方式，尤其是正交幅度调制(QAM)得到了大量的应用，从早期的4QAM到今天的16QAM。高阶QAM调制大容量数字微波通信系统为了保证服务质量，降低误码率，-long with the increase of information capacity and frequency resource scarcity, for improving the utilization ratio, unit of microwave communication bandwidth used more and more in the system of multilevel much phase modulation method complex signal amplitude modulation Platform: |
Size: 629760 |
Author:蒋梦琪 |
Hits:
Search - bandwidth in matlab